Bending LED light strips can be a difficult task at times. That’s why this question often comes to mind: “How to Bend LED Strip Lights?” But contrary to widespread belief, it is one of the easiest DIY projects. It does not necessitate the use of any instruments or special abilities. It takes only ten minutes to complete.
That’s all there is to it. You have to be patient and careful when bending the light strip. Scotch tape is the only tool required for this procedure. Here’s how to bend your LED strip lights if you want to give it a shot: Step-by-Step Instructions on Bending LED Light Strips.
How to Bend LED Strip lights?
The LED strip lights have an adhesive backing that can be mounted on flat surfaces; nevertheless, the installation process frequently needs the strips bent around curves and corners. Use these simple tactics to get the most out of your LED lights for the most outstanding results to bend your LED strip lights.
Technique One: By Cutting and Jumping with connector
One option is to purchase an LED strip light jumper connector, cut the strip light in half, and then connect the connector in the middle. This enables you to bendLED Strip Light 90 Degree Corner Connectors the two strip light portions in whichever way you wish. If you don’t have a bendable LED strip or are concerned about breaking it, using a connection is the best solution.
The most significant disadvantage of using a jumper connector for corner placement is the need for soldering. You can, however, buy connectors that don’t require soldering. I’m a naturally lazy person who is determined to find a quicker solution.
Technique Two: By Folding the LED strip at 90° angle
Follow these procedures during installation to get a smooth, clean corner fold.
- Lay the flex strip out straight and identify the location where the fold will be made.
- Begin by folding flex back at a 45° angle in the direction opposite the corner you need to round.
- Bend flex back on itself in the proper direction to create a 90° angle.
- Press firmly to the crease; if desired, use a dab of super glue to secure the fold.
Technique Three: By Pincing the LED strip at 90° angle
This method is recommended for situations where the flex strips will be hidden, and the finished look of the 90° fold is not required. Pinch the flex between LED components into a peak for a more streamlined corner turn. Apply a dab of super glue to the pinch to keep it in place.
Technique Four: By curving the LED strip lights
Make a sequence of modest accordion folds spaced several inches apart to make a more progressive rotation. This method is best used in areas with rounded edges and angles greater than 90 degrees. To secure each fold, a small dab of super glue can be applied.
LED Strip Light 90 Degree Corner Connectors
You’ll need “L Shaped” back-to-back pin connectors if you wish to make a continuous 90-degree rotation with your LED light strips.
This is a quick technique to cut your strip lights where they’re needed and turn 90 degrees with minimal light gaps.
Strip Light Connectors Back to Back
It’s pretty easy to use plastic back-to-back light strip connectors. Make sure you’re looking for the right amount of pins for your light strips.
Selecting the Correct Pin Connectors
Copper connection markings are found on most LED light strips every inch or two along the length of the strip. This is usually where you can cut.
LED light strip manufacturers are not all the same. You’ll need to know whether your copper connection is two pins, four-pin, or five pins.
Different back-to-back connectors are designed to only function with specific copper connecting locations on LED light strips.
Selecting the Proper Connector Width
The most common LED light strip width is 3/8′′ (or 10mm). It’s critical to have the proper connector width for your light strips since a cut part of strip light must connect with the pins within the back-to-back connector.
Make sure you’re using the correct polarity (+ goes to +)
It’s most likely the polarity if you’re scratching your head after an installation and wondering why your light strips aren’t working.
This is why it’s critical to align your connections and ensure that they’re secure.
Ensure the “+” markings on the two sections of the cut light strip match the other “+” when connecting them to the back-to-back connector pins. Also, make sure the RGB letters are aligned with one another.
To know the Best led strip light connectors you can take a look through this article! But here we are, providing a shortlist of LED strip light connectors from our list!
2 Pin: LightingWill LED Strip Connector
The LightingWill LED Strip Connector is a two-pin connector is 10mm wide SMD5050 5630 single-color LED strips.
It can withstand up to 4A current and 0-24V voltage; heat resistance ranges from -20 to 100 degrees Celsius.
It has a clip to strip one end and wires as a lead on the other. It works with both waterproof and non-waterproof light strips.
Pros:
√ Modern style
√ Durable and powerful
√ Consistent with both waterproof and non-waterproof light strips
Cons:
× Quite expensive
× Not contain wires or strip lights.
3 Pin: ACTOR JST SM 3 Pin LED Connector
The ACTOR JST SM 3 Pin LED strip light Connector is made of a plastic material easily peeled off. It measures 5.91 inches (15cm) in length and has a wire diameter of 1.5mm.
Each wire has been pre-stripped and tinned, and the tinning is fine enough that you can poke it right into a microcontroller board and solder it up in a matter of seconds.
The insulation keeps the heat out and gives the hacks a more professional appearance. This is pretty much the industry standard for WS2812B devices, so having a whole bag of these on hand isn’t a bad idea.
Pros:
√ The wire is pre-stripped and pre-tinned
√ Tinned copper wire
√ No soldering
√ Easy return policy
Cons:
× Connectors may be missing in the package
4 Pin: WENHSIN RGB LED Light Strip Connectors
WENHSIN RGB LED Light Strip Connectors work with 0.39in / 10mm wide SMD 5050 RGB Flexible LED Strips. Only solderless couplers for 10mm waterproof RGB LED strips are available.
To make a connection without compromising the silicone, pins pierce the strip from behind. Only suitable for standard density strips.
These are made specifically for use with silicone-coated waterproof strips.
Pros:
√ Solder less couplers
√ Designed especially for waterproof strips
√12 months return policy with 12 month guarantee.
Cons:
× Hard to open
× Quite expensive compare to other