How to Install Car LED Light Strips?

Share this Article

To install car LED light strips, gather the necessary materials, including the LED light strips, control module (if applicable), power source (such as a fuse tap or cigarette lighter adapter), wire connectors, electrical tape, and zip ties. Plan where to place the light strips, clean the surface, and cut the strips to the desired length. 

Connect the LED light strip wires to the control module, and then connect the power wires to the chosen power source, ensuring proper polarity. Test the lights, secure the light strips using zip ties or adhesive backing, and route the wires neatly. 

Double-check all connections, insulate any exposed wires with electrical tape, and ensure compliance with local regulations. Enjoy your newly installed car LED light strips by turning them on and customizing the settings to your preference.

In this content, you will learn a step-by-step guide on how to install car LED light strips. Keep reading till the end to learn everything about the installation process of LED strip lights in a car.

How to install car-led light strips?

Installing car LED light strips can be a fun and attractive way to change the look of the inside or outside of your car. Here’s a step-by-step guide to putting LED light strips on a car:

Gather the necessary materials

Before you start, ensure you have everything you need, like LED light strips, a control module (if needed), a power source (like a fuse tap or car lighter adapter), electrical tape, wire connectors, and zip ties.

Plan the placement

Choose where in your car you want to put the LED light strips. Some common places are under the dashboard, along the footwell, or under the seats. You may also want to put them outside your car to add accent lights. When deciding where to put the LED strips, you should consider how long they are and how they will be charged.

Prepare the surface

Clean and dry the area where the LED light strips will go. Use isopropyl alcohol to remove any dirt, dust, or residue that might make it hard for things to stick.

Connect the LED light strips

Cut the LED light strips to the length you want or as the maker tells you to. Most LED light strips have places where they end. Strip the ends of the wires on the LED light strips and use wire connectors to connect them to the control module, if needed. Follow the steps from the maker to make sure the connections are right.

Connect the power source

Figure out how you want your LED light strips to be powered. You can connect them straight to the car battery or make installation easier using a fuse tap or cigarette lighter adapter. Connect the power lines carefully to the chosen power source, making sure the polarity is correct, and the connections are tight.

Test the lights

Test the LED light strips to ensure they work right before putting them in place. Turn on your car and see if the lights work as they should. Suppose they don’t check the links again and figure out what’s wrong.

Secure the LED light strips

Once you’re happy with how the LED light strips work, you can put them where you want. Use zip ties or the sticky backing that came with them to keep them in place. Ensure the wires are neatly tucked away and won’t get in the way of moving parts or cause a safety danger.

Route the wires

Carefully route the wires from the LED light strips to the power source. Make sure the wires are hidden or tucked away nicely to keep the area looking clean. You can fix the wires along the inside panels or under the car with zip ties or adhesive clips if you need to.

Finalize the installation

Check each link twice to make sure it is secure and insulated. Cover any uncovered wires with electrical tape or a wire loom to prevent damage.

Enjoy your LED lights

Turn on your car and enjoy the bright light from the LED light strips you just put in. You can change the color, brightness, or effects by changing the settings on the control box if there is one.

How to install LED lights in the car interior?

Preparation

You’ll need to buy the lights themselves before you can put them up. Getting an LED light kit for your car can make your life much easier. Kits will come with a power source that plugs into your car’s 12V lighter socket, a controller that lets you switch between light settings, likely with a remote and/or your phone, and the LED light strips themselves. The outside lights should have a waterproof cover to protect them.

Preparing some things besides what’s in the box would be good. To make the fitting process easier, you might want to have some extra help with sticking. The 3M tape can stick better if strong glue bonds well to the car’s metal.

You’ll want to make sure that the strips are attached in a way that makes them ready for the car’s movement, bad weather, and the natural wear and tear that comes with time. Zip-ties work great, too. And if you want to be extra safe, you could even drill some holes for screws and put little frames on the lights to hold them in place.

Installation

Now, let’s talk about the actual installation:

Plan

Make sure you know where you will put the lights. Some places that look good might be too hidden, blocking the lights and making them shine less brightly. Use a small hand-held light to see what the LED lights will look like once installed. Consider where the lights will go, draw a map, and measure it.

Test the Lights

Plug in the lights and make sure they work right. You wouldn’t want to put in the effort to install them only to find out they don’t work right. Then, lightly tape it with some Scotch tape along the lines you’ve drawn to ensure the length is right before using the real glue. You can move them around and better understand how they will be put together.

Clean the Area

Use a wet cloth or alcohol spray to clean the area where the lights will go. This will get rid of any dust that might be there. Before fitting, sand the area and clean it well if it is rough or has dried mud.

After Cleaning

After cleaning, give the area enough time to dry and one last sweep to ensure no dust is left behind. Then, start removing the paper from behind the lights and putting them back where they belong.

As needed, reinforce them

When you put them in place, make sure they are well-anchored so they can stand up to rough times in the future. As was already said, ensure they are safe to withstand light hits, scrapes, dust, weather, etc. If you need to, you can hold them in place with more glue, zip ties, or even braces you drill. No matter how you do it, ensure they won’t fall off.

Start Playing

Now that the lights are up, the glue is dry, and the power is plugged in, it’s time to use them! Use the app or remote to turn them on, and then start playing around with the different settings. Try playing different songs and watch how the RGBIC chip syncs to the beat to make the lights dance with you. Figure out how much light you want inside so it doesn’t bother you. Match the outside color to the color of your car’s paint, or go all out with the random color setting.

Note: Check with your local government to see if there are any rules about lights outside. For example, blue and red lights are often not allowed because they can be confused with police lights. 

Final Words

Remember to refer to the specific instructions provided by the manufacturer of your LED light strips, as installation methods may vary. Additionally, it’s essential to comply with local regulations regarding using decorative lighting on vehicles to ensure safety and legal compliance.

Leave a Comment